|
|
 Rank: Pro   Groups: Registered
Joined: 29/03/2010 Posts: 190 Points: 512 Location: Lytham UK
|
Hi , Tomick and every one.... I have noticed a difference in the stern build from magazine to on line. I have attached two pictures one shows a three plank gap at the rear ( in magazine ) and the on line build shows only one. Is it important on which one is followed? Regards, Ian IAN attached the following image(s): Ian Builds in progress: E-type, HMS Victory, HMS Endeavour, HMS Soverein of the Seas Wish list: Bentley Blower http://forum.model-space...spx?g=posts&m=30439
http://mxpublishing.co.uk/engine/shop/product/9781780920184/Hunt+for+the+Blower+Bentley
|
|
|
 Rank: Vice-Master  Groups: Registered
Joined: 20/04/2010 Posts: 545 Points: 1,536 Location: lossiemouth
|
count the port holes in the two pictures you will see where you are confused there is three more aft
|
|
|
 Rank: Master  Groups: Registered
Joined: 15/04/2010 Posts: 1,266 Points: 3,841 Location: The Quantock Hills,Somerset
|
Willie,I think you are mis reading this,if you look at the 2 pics,the online one shows a 1 plank vertical & then a slope above stern gallery,the magazine shows a 3 plank vertical then the slope. I'm afraid I can't help you Ian as I am yet to start the planking but i'm sure someone will be able to help you. Rob Nolli Illigitimi Carborundum!!!Current Builds: HMS Victory, SV Thermopylae
|
|
|
Rank: Vice-Master Groups: Registered
Joined: 20/04/2010 Posts: 545 Points: 1,536 Location: lossiemouth
|
well mine is about 11/2 planks there i go buy the cut out template at that point
|
|
|
Rank: Vice-Master Groups: Registered
Joined: 25/04/2010 Posts: 748 Points: 2,285 Location: bognor regis
|
we have spotted a couple of errors with the mag build before..i have already planked the upper half of my build and mine is the same as tomicks...cheers paul cheers benny
|
|
|
Rank: Pro Groups: Joined: 24/08/2009 Posts: 48,827 Points: -13,348
|
Ian, when you apply the stern template, you should find that the step before it goes off at an angle is approx the width of one plank as per my photo, so the advice is to follow the line of the template rather than what you see in planks.
|
|
|
Rank: Pro Groups: Registered
Joined: 29/03/2010 Posts: 190 Points: 512 Location: Lytham UK
|
To.. Tomick - dontshootme - Benny - Willie - . Many thanks for your help and input. Regards, Ian Ian Builds in progress: E-type, HMS Victory, HMS Endeavour, HMS Soverein of the Seas Wish list: Bentley Blower http://forum.model-space...spx?g=posts&m=30439
http://mxpublishing.co.uk/engine/shop/product/9781780920184/Hunt+for+the+Blower+Bentley
|
|
|
Rank: Vice-Master Groups: Registered
Joined: 25/04/2010 Posts: 748 Points: 2,285 Location: bognor regis
|
anytime ian just ask...paul cheers benny
|
|
|
Rank: Vice-Master Groups: Registered
Joined: 20/04/2010 Posts: 545 Points: 1,536 Location: lossiemouth
|
that what the form for even if we do get a bit muddle
|
|
|
|
Guest
|
US
