Welcome Guest Search | Active Topics | Log In | Register

Rossi Yamaha YZR-M1 Official Build Diary - Pack 10 (USA) Options
Spal
#1 Posted : 22 July 2019 00:27:06

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 19/06/2013
Posts: 4,588
Points: 13,553
Location: West Yorkshire
Pack 10 contains parts for stages 36-39

Stage 36

Contents:Left manifold, Right manifold, Left throttle body, Right throttle body, Throttle return rod.

Note error in instructions
Part A labelled left manifold is in fact the right manifold.
Part B labelled right manifold is in fact the left manifold.
Step 01 photo shows right side parts not left as stated.
Step 03 photo shows left side parts not lright as stated.

Take the left manifold and the left throttle body, and align the parts as shown.Join the manifold to the throttle body by pressing the two together. Check that the orientation of the pieces is exactly like that in the picture.Repeat these steps for the right manifold and throttle body.Insert the pins at the bottom of the left throttle body into the holes in the engine block, making sure that the circled hole is outermost.Repeat this with the right throttle body by placing it into the holes in the engine block, making sure that the circled hole is outermost. Insert the pins at the ends of the throttle return rod into the indicated holes in the throttle bodies.

Stage complete, carefully store any remaining parts in a stage labelled bag.
Spal attached the following image(s):
IMGL2295.JPG
IMGL2298.JPG
IMGL2299.JPG
IMGL2300.JPG
IMGL2301.JPG
IMGL2302.JPG
IMGL2303.JPG
IMGL2304.JPG
IMGL2305.JPG
IMGL2306.JPG
Spal
#2 Posted : 22 July 2019 00:28:58

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 19/06/2013
Posts: 4,588
Points: 13,553
Location: West Yorkshire
Stage 37

Contents: Support rod A, Support rod B, Side covers, Right intake ducts, Left intake ducts.

Take one of the side covers, and insert the ends of the two support rods, A and B, into the correct holes.Fit the second side cover onto the other ends of the two support rods.Insert the two pins on the first side cover into the holes in the right intake ducts.Fit the left intake ducts to the other side cover, in the same way as the right were fitted.Retrieve the airbox (from Stage 22) and place the ducts inside, fitting them onto the posts as shown.Retrieve the upper part of the airbox (from Stage 21), then place it onto the lower part and lock them together.

Stage complete, carefully store any remaining parts in a stage labelled bag.

Spal attached the following image(s):
IMGL2307.JPG
IMGL2309.JPG
IMGL2310.JPG
IMGL2311.JPG
IMGL2312.JPG
IMGL2313.JPG
IMGL2314.JPG
IMGL2315.JPG
IMGL2316.JPG
IMGL2317.JPG
IMGL2318.JPG
IMGL2319.JPG
Spal
#3 Posted : 22 July 2019 00:31:20

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 19/06/2013
Posts: 4,588
Points: 13,553
Location: West Yorkshire
Stage 38

Contents: Upper right coupling, Upper left coupling, Couplings (x 2), Thick tubes, Thin tubes, Exhaust gaskets.

Take the two couplings A and B and fit them into the ends of the two thick tubes. The tubes must be exactly 45mm long. Position the engine so that you can work on the right-hand side. Insert the end of coupling A into the hole at the side of the engine block, and place the other end of the tube onto the pin on the engine front.Now fit coupling B to the hole on the left-hand side of the engine and the tube to the pin at the engine rear.Take the couplings C, and fit them into the ends of the thin tubes, cut to lengths of 70mm and 60mm.Insert the two couplings C into the holes in the righthand side of the engine, ensuring the 60mm tube is in top hole.Secure them with some adhesive if necessary.Take the two gaskets marked R2 and L2 and fit these to the matching points on the engine, apply some adhesive if necessary.

Stage complete, carefully store any remaining parts in a stage labelled bag.
Spal attached the following image(s):
IMGL2320.JPG
IMGL2321.JPG
IMGL2322.JPG
IMGL2323.JPG
IMGL2324.JPG
IMGL2325.JPG
IMGL2326.JPG
IMGL2328.JPG
IMGL2329.JPG
IMGL2330.JPG
IMGL2331.JPG
IMGL2332.JPG
IMGL2333.JPG
IMGL2334.JPG
IMGL2335.JPG
IMGL2337.JPG
Spal
#4 Posted : 22 July 2019 00:37:12

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 19/06/2013
Posts: 4,588
Points: 13,553
Location: West Yorkshire
Stage 39

Contents: Shock absorber body, Spring, Shock absorber rod, Type P screws, Type U screws.

Take the shock absorber body and place the spring onto it then insert the shock absorber rod down through the spring into the shock absorber body, so that the window in the rod is aligned with the circled hole in the body.Tighten a screw U into the hole in the shock absorber body, this should secure the shaft in place.Insert the end of the shock absorber body into the mount at the rear of the engine assembly.Insert a type P screw through the aligned holes and tighten the screw into place to secure the shock absorber to the engine.

Stage complete, carefully store any remaining parts in a stage labelled bag

Spal attached the following image(s):
IMGL2341.JPG
IMGL2342.JPG
IMGL2343.JPG
IMGL2344.JPG
IMGL2345.JPG
IMGL2346.JPG
IMGL2347.JPG
IMGL2348.JPG
IMGL2349.JPG
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.140 seconds.
DeAgostini