|
|
 Rank: Pro     Groups: Registered
Joined: 25/04/2014 Posts: 370 Points: 1,122 Location: Mandurah W.Australia
|
birdaj2 wrote:John
That looks wonderful.
Your hard work has really paid off with a nice model.
Tony Hi Tony Yeah it is hard work, but very satisfying in the long run...  Thanks for the compliment...  Regards JohnP
|
|
|
Rank: Pro Groups: Registered
Joined: 25/04/2014 Posts: 370 Points: 1,122 Location: Mandurah W.Australia
|
Gandale wrote:Beautiful John, you're doing a fabulous job on her.....  Regards Alan Hi Alan Thanks for the nice compliment and I hope you can help me with a problem....  I ran out of 0.25mm fawn rigging thread today and had intended to begin a new roll purchased from a supplier in Melbourne about 2 months ago. Unfortunately this thread doesn't match that supplied by De-Ag. Both colour and thickness are different.  See photo. Can you advise if there is a supplier in UK I can contact inline?... Maybe they will have the stand as well then I can can order both.... I need the same thread for continuity, I'm sure you'll agree... John Passmore attached the following image(s):
|
|
|
Rank: Pro Groups: Registered
Joined: 25/04/2014 Posts: 370 Points: 1,122 Location: Mandurah W.Australia
|
Markwarren wrote:Nice work John, looks stunning.  Mark Hi Mark Thanks for looking in and the nice compliment....I think I'll maybe have it completed within the next six months... Regards JohnP
|
|
|
|
|
Hi John, Have you considered purchasing a back issue, one that contains the size of thread you need. You could try emailing sales@model-space.co.uk outlining your problem and quoting the issue number you would like to purchase, they may be able to help. If that doesn't work then by all means get back to me.... Regards Alan
|
|
|
Rank: Pro Groups: Registered
Joined: 25/04/2014 Posts: 370 Points: 1,122 Location: Mandurah W.Australia
|
Gandale wrote:Hi John, Have you considered purchasing a back issue, one that contains the size of thread you need. You could try emailing sales@model-space.co.uk outlining your problem and quoting the issue number you would like to purchase, they may be able to help. If that doesn't work then by all means get back to me.... Regards Alan Thanks Alan, I'll try that - maybe Model-Space has an agency in Oz as well?... Appreciate your advice... Regards JohnP
|
|
|
Rank: Pro Groups: Registered
Joined: 25/04/2014 Posts: 370 Points: 1,122 Location: Mandurah W.Australia
|
John Passmore wrote:Gandale wrote:Hi John, Have you considered purchasing a back issue, one that contains the size of thread you need. You could try emailing sales@model-space.co.uk outlining your problem and quoting the issue number you would like to purchase, they may be able to help. If that doesn't work then by all means get back to me.... Regards Alan Thanks Alan, I'll try that - maybe Model-Space has an agency in Oz as well?... Appreciate your advice... Regards JohnP Hi Alan I happily purchased the thread from Model-Space UK, who were very helpful. I received the goods in about 3 weeks from my initial inquiry... and I purchased the display stand at the same time... Regards JohnP
|
|
|
Rank: Pro Groups: Registered
Joined: 25/04/2014 Posts: 370 Points: 1,122 Location: Mandurah W.Australia
|
Hi Everyone Here is my progress to end December 2019. Issues 129 and 130 refer. Figured out how to make rope coils to go onto the belaying pins. Looks more realistic now... Have more to do as I proceed... * Made up and installed Bowsprit sails and rigging... * Installed Mizzen mast spar V11 with rigging... Had a few accidents along the way - couple of busted halyards and other bits of running rigging pulled out...  Regards to All and a Happy New Year JohnP John Passmore attached the following image(s):
|
|
|
|
|
Stunning work John.... Going to be a fabulous display model once done.... .. Very well done.... Regards Alan
|
|
|
 Rank: Super-Elite     Groups: Registered
Joined: 31/05/2010 Posts: 5,679 Points: 17,011 Location: Wiltshire
|
Looks very nicely done and very precise John. Not long mow until you finish this one. Tony Happy Modelling
BUILDING: Hachette Spitfire Mk 1A, Constructo Mayflower
SUBSCRIPTION COMPLETE (Awaiting building): USS Constitution, Sovereign of the Seas, 1:200 Bismarck (Hachette)
COMPLETED: Porsche 911, E-Type Jaguar, Lam Countach
|
|
|
Rank: Pro Groups: Registered
Joined: 25/04/2014 Posts: 370 Points: 1,122 Location: Mandurah W.Australia
|
Gandale wrote:Stunning work John.... Going to be a fabulous display model once done.... .. Very well done.... Regards Alan Hi Alan Thanks for the nice words. Got an update coming up in a minnit... Regards JohnP
|
|
|
Rank: Pro Groups: Registered
Joined: 25/04/2014 Posts: 370 Points: 1,122 Location: Mandurah W.Australia
|
birdaj2 wrote:Looks very nicely done and very precise John.
Not long mow until you finish this one.
Tony Hi Tony Thanks for the compliment and yeah - I can see the light at the end of the tunnel...  Regards JohnP
|
|
|
Rank: Pro Groups: Registered
Joined: 25/04/2014 Posts: 370 Points: 1,122 Location: Mandurah W.Australia
|
Hi Everyone Just a quick update - issues 130 and 131 refer * Installed Lateen sail - not happy with it as it sits too low, will have to adjust it...  * Fitted Yard V11 - no problems... Regards to all JohnP John Passmore attached the following image(s):
|
|
|
|
|
Hi John, lovely work on the SotS Looking at your pictures the lateen sail is the wrong way round. The panel with the reef lines should be horizontal to the deck . Hope this helps Martyn Building ?
Completed. Soliei Royal . Sovereign of the Seas . Virginia . Scotland . San Felipe . Corel vasa , Santisima Trinadad X section , Vasa
Next Build ?
When sailors have good wine, They think themselves in heaven for the time. John Baltharpe
|
|
|
Rank: Pro Groups: Registered
Joined: 25/04/2014 Posts: 370 Points: 1,122 Location: Mandurah W.Australia
|
Hi again Everyone Further to my previous post here is a little problem I had with fitting of the sailSA12... I had installed braces from yard V8 incorrectly, blocks were on middle mizzen shrouds should have been on the lower mizzen shroud... Have to disconnect and place correctly... Inattention on my part! Regards JohnP John Passmore attached the following image(s):
|
|
|
Rank: Pro Groups: Registered
Joined: 25/04/2014 Posts: 370 Points: 1,122 Location: Mandurah W.Australia
|
Martyn Ingram wrote: Hi John, lovely work on the SotS Looking at your pictures the lateen sail is the wrong way round. The panel with the reef lines should be horizontal to the deck . Hope this helps Martyn Hi Martyn You nearly gave me a heart attack (another one)!!! But I have checked Issue 130 item 21 and the picture clearly shows it vertical with the deck...or have I missed something? Thanks for the nice compliments Regards JohnP
|
|
|
|
|
 Sorry John I think I'll have to go to the opticians  just looked at mine and it's the same as yours . Should have done that before I posted. She is a great kit to build and yours is turning into a stunner, well done m8 Martyn Building ?
Completed. Soliei Royal . Sovereign of the Seas . Virginia . Scotland . San Felipe . Corel vasa , Santisima Trinadad X section , Vasa
Next Build ?
When sailors have good wine, They think themselves in heaven for the time. John Baltharpe
|
|
|
Rank: Pro Groups: Registered
Joined: 25/04/2014 Posts: 370 Points: 1,122 Location: Mandurah W.Australia
|
Hi Everyone Latest progress to end January 2020 Issue 131 refers Installed last 2 Mizzen sails SA12 and 13...Yippee! all sails now done and dusted!.... Just the anchors, figures, flags and some added rope coils on the belay pins... Regards JohnP John Passmore attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Registered
Joined: 31/05/2010 Posts: 5,679 Points: 17,011 Location: Wiltshire
|
Very neat work John. All that rigging looks extremely complex. Tony Happy Modelling
BUILDING: Hachette Spitfire Mk 1A, Constructo Mayflower
SUBSCRIPTION COMPLETE (Awaiting building): USS Constitution, Sovereign of the Seas, 1:200 Bismarck (Hachette)
COMPLETED: Porsche 911, E-Type Jaguar, Lam Countach
|
|
|
|
|
Looking fab John, the end is very much in sight now.... .. Very well done... Regards Alan
|
|
|
Rank: Administration  Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,251 Points: 23,841 Location: East midlands
|
Great build John Regards delboy271155 (Derek) COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
|
|
|
|
Guest (4)
|
US
