Welcome Guest Search | Active Topics | Log In | Register

Rossi Yamaha YZR-M1 Official Build Diary - Pack 24 (USA) Options
Spal
#1 Posted : 17 June 2020 16:02:12

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 19/06/2013
Posts: 4,588
Points: 13,553
Location: West Yorkshire
Pack 24 contains parts for stages 90-91

Stage 90

Contents: Right fairing, Type D screws x 2, Type H screws x 3

Retrieve the tank (Stage 4) and two type A screws (Stage 89). Place the tank onto the frame, aligning the holes at the sides. Tighten a type A screw into the aligned holes on both sides. Place the seat between the rear fairing and the fuel tank, aligning the hole at the rear with the corresponding hole in the top of the rear fairing. Use a type K screw to secure the seat. Fix the front of the seat in place with a type K screw on either side.

Stage complete, carefully store any remaining parts in a stage labelled bag
Spal attached the following image(s):
IMGL4243.JPG
IMGL4244.JPG
IMGL4246.JPG
IMGL4248.JPG
IMGL4251.JPG
Spal
#2 Posted : 17 June 2020 16:03:58

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 19/06/2013
Posts: 4,588
Points: 13,553
Location: West Yorkshire
Stage 91

Contents: Left fairing lower, Type H screws x 3

Mount the left fairing (Stage 89) onto the left side of the frame aligning all of the corresponding holes. Fix the fairing at the front with two type H screws and secure the rear of the fairing with a type W screw. Place the right fairing (Stage 90) onto the right side and secure the front end with two type H screws and the rear of the fairing with a type D screw.

Stage complete, carefully store any remaining parts in a stage labelled bag
Spal attached the following image(s):
IMGL4252.JPG
IMGL4253.JPG
IMGL4254.JPG
IMGL4257.JPG
Spal
#3 Posted : 17 June 2020 16:08:36

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 19/06/2013
Posts: 4,588
Points: 13,553
Location: West Yorkshire
Stage 92

Contents: Right fairing lower, Tail hole cover, Type H screws x 4

Take the left fairing lower (Stage 91) and fit it to the bottom of the left fairing, inserting the pins into the holes. Fix the fairing lower to the bottom of the left fairing with three type H screws. Now fit the right fairing lower (Stage 92) to the bottom of the right fairing and the inside of the left fairing lower. Make sure all the parts are properly aligned and then secure the fairing lower with three more type H screws. Take the tail cover and remove the backing from it and fit it into the hole in the tail.

Congratulations! Your Valentino Rossi’s Yamaha YZR-M1 is now complete.
Spal attached the following image(s):
IMGL4258.JPG
IMGL4259.JPG
IMGL4260.JPG
IMGL4262.JPG
IMGL4263.JPG
IMGL4268.JPG
IMGL4269.JPG
IMGL4270.JPG
IMGL4271.JPG
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.146 seconds.
DeAgostini