|
|
Rank: Administration        Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,282 Points: 23,934 Location: East midlands
|
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,282 Points: 23,934 Location: East midlands
|
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,282 Points: 23,934 Location: East midlands
|
Hi all, last one for today, honestly.  
I`ve had a couple of packs delivered due to a previous delay, so I`m playing catch-up and as these updates are relatively small, thought I`d give a few for you to peruse.
So, this is the update for issue 19 and completes the thumb for the time being.
Parts for this issue are shown in Pic 1.
The first part of this update is very easy, so position part D04 inside part A73 and secure them together with an 01 type screw. (black) Pic 2.
Please take note:
The second part to this update needs some care to be taken or damage to parts may occur.
Part A73 can only fit in one orientation, that can be seen by the ridges and lines in the part. By placing the part over the thumb you should see how the parts line up. When happy with the line-up of the parts, part D04 (inside A73) should be directly above the oblong hole in the central thumb joint. Now make sure that the parts stay in line and whilst holding the thumb from the underside, press A73 down onto the thumb. Part D04 should click into place and form the armour plate for the central knuckle joint of the thumb. Pic 3. Another point to note is that the Arrow in Pic 3 is where you need to apply pressure to lock the parts together.
That ends this update, so I`ll see you all soon for issues 20 and 21 and close this pack. Just one thing to note: At this point I weighed the thumb on my kitchen scales and it hit 496 gms. 
Hoping to start the next pack construction (Issues 22 - 26) very soon, so keep in touch. 
Regards
delboy271155
(Derek) Admin delboy271155 attached the following image(s): COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,282 Points: 23,934 Location: East midlands
|
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,282 Points: 23,934 Location: East midlands
|
Welcome back, 
This is the last update for this pack, Issue 21.
Its very similar to the last issue with the same amount of work to be done.
Issue 21 parts are shown in Pic 1.
Bring the final assembly back from the last update and if you replaced the stones, remove them again to save causing any damage.
Working on the inside of the previous assembly, fit and secure part A23 with 3 x type 01 screws. Pic 2.
Pic 3 shows the outside of the Gauntlet with the stones replaced and Pic 4 shows how the back of the Gauntlet now looks at the end of this pack.
Work on the next pack is underway and will be posted soon, covering issues 22 - 26.
Until then take care.
Regards
delboy271155
(Derek) Admindelboy271155 attached the following image(s): COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
|
|
|
|
Guest
|
US
