Welcome Guest Search | Active Topics | Log In | Register

Batmobile Official Build Pack 5 Options
Markwarren
#1 Posted : 22 June 2024 12:14:59

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds

Joined: 04/01/2016
Posts: 6,471
Points: 19,727
Location: Northamptonshire, England
Issue 15

Picture 1 shows the parts for this issue.

Fitting the Fuel Line

Take the fuel line (15B) and push one end onto the pin on the side of the fuel filter as shown in picture 2 and 3.

Preparing the Front Chassis
The front chassis (15A) come with a beam attached to protect it during transportation. Remove the beam from the chassis by removing the two screws that hold it in place, picture 4.

Picture 5 shows the complete assembly for this issue.
Markwarren attached the following image(s):
15 (1).jpg
15 (2).jpg
15 (3).jpg
15 (4).jpg
15 (5).jpg
Markwarren
#2 Posted : 22 June 2024 12:22:10

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds

Joined: 04/01/2016
Posts: 6,471
Points: 19,727
Location: Northamptonshire, England
Issue 16

Picture 1 shows the parts for this issue.

Fitting the Crossmember

Take the front chassis rear frame (16A) and the chassis rear crossmember and connect them together using a GM screw. Pictures 2 and 3.

Fitting the Front Chassis Rear
Take the part you’ve just assembled and fit it to the front chassis with 2 x EM screws as shown in picture 4.

Picture 5 shows the complete assembly for this issue.


Markwarren attached the following image(s):
16 (1).jpg
16 (2).jpg
16 (3).jpg
16 (4).jpg
16 (5).jpg
Markwarren
#3 Posted : 24 June 2024 09:28:58

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds

Joined: 04/01/2016
Posts: 6,471
Points: 19,727
Location: Northamptonshire, England
Issue 17

Picture 1 shows the parts for this issue.

Installing the Bumper

Take the front left lower suspension arm (17B) and the bumper (17C) and using 2 x AM screws secure the parts together, pictures 2 and 3.

Threading the Screw Holes
Screw two AHM screws in the ends of the two posts as shown in picture 4, and then remove them.

Fitting the Arm to the Crossmember
Use one of the AHM screws to attach the front left lower suspension arm to the crossmember, picture 5.

That completes the assembly for this issue.
Markwarren attached the following image(s):
17 (1).jpg
17 (2).jpg
17 (3).jpg
17 (4).jpg
17 (5).jpg
Markwarren
#4 Posted : 29 June 2024 12:32:11

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds

Joined: 04/01/2016
Posts: 6,471
Points: 19,727
Location: Northamptonshire, England
Issue 18

Picture 1 shows the parts for this issue.

Installing the Bumper

Take the front right lower suspension arm (18B) and the bumper (18C) and using 2 x AM screws secure the parts together, pictures 2 and 3.

Fitting the Bracket and Crossmember
Screw two AHM screws in the ends of the two posts in the engine mounting bracket (18A) as shown in picture 4, and then remove them.
Use one of the AHM screws to attach the front right lower suspension arm to the crossmember, pictures 5 and 6.
Now secure the engine mounting bracket to the two suspension arms using two AHM screws, picture 7. Picture 8 shows the complete assembly.

Installing the Engine
Secure the front crossmember and engine mounting bracket to the front of the chassis using 4 x CM screws as shown in pictures 9 and 10.

Now take the engine assembly and place it on the chassis parts so that the left and right engine brackets are slotted into the engine mounting bracket. Secure both sides with an AM screw as shown in pictures 11 and 12.

Finally, secure the gearbox section to the front chassis with a CM screw, picture 13.

That completes the assembly for this issue.

Markwarren attached the following image(s):
18 (1).jpg
18 (2).jpg
18 (3).jpg
18 (4).jpg
18 (5).jpg
18 (6).jpg
18 (7).jpg
18 (8).jpg
18 (9).jpg
18 (10).jpg
18 (11).jpg
18 (12).jpg
18 (13).jpg
Markwarren
#5 Posted : 29 June 2024 13:11:29

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds

Joined: 04/01/2016
Posts: 6,471
Points: 19,727
Location: Northamptonshire, England
Issue 19

Picture 1 shows the parts for this issue.

Fitting the Left and Right Covers

Place the left front and rear covers (19A and 19B) on the chassis and secure each cover with 2 x AM screws as shown in picture 2. Now do the same with the right-side covers (19C and 19D), picture 3.

Fitting the Left and Right Bolts
Using a KP screw, secure the stabiliser link bolt (19G) to the left side bumper, picture 4. Next, fit the right-side stabiliser in the same way using a KP screws, picture 5.

Installing the Stabiliser and Brackets
Place the stabiliser (19E) so the arms at each end can fit around the two stabiliser link bolts, picture 6. Picture 7 shows the stabiliser in place.

Secure the stabiliser by attaching the two stabiliser brackets (19F) to the front chassis as shown in pictures 8 and 9.

Picture 10 shows the complete assembly for this issue.
Markwarren attached the following image(s):
19 (1).jpg
19 (2).jpg
19 (3).jpg
19 (4).jpg
19 (5).jpg
19 (6).jpg
19 (7).jpg
19 (8).jpg
19 (9).jpg
19 (10).jpg
Markwarren
#6 Posted : 30 June 2024 16:33:02

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds

Joined: 04/01/2016
Posts: 6,471
Points: 19,727
Location: Northamptonshire, England
Issue 20

Picture 1 shows the parts for this issue.

Fitting the Arm Balls and Assembling the Upper Suspension Arm

Using 2 x WM screws, attach the lower arm ball (20G) to the bottom of the steering spindle arm (20F) and the upper arm ball (20G) to the top of the steering spindle arm, pictures 2 and 3.

Fit the shaft (20D) to the shock absorber mount (20C) with 2 x CM screws, picture 4. Take the assembly and attach it to the front left upper suspension arm (20E) with 2 x EM screws, picture 5.

Fitting the Shoch Absorber
Insert the shock absorber coil spring (20B) between the front left lower suspension arm and front chassis, picture 6. Insert the shock absorber rod through the centre of the spring from the bottom and securing it with an AIM screw from the top of the chassis, picture 7. Secure the rod at the bottom by using 2 x AM screws, picture 8.

Fitting the Upper Arm
Fit the steering spindle arm to the lower suspension arm with an AIM screw, picture 9. Finally, secure the shock absorber mount to the front chassis using 2 x CM screws, picture 10.

Picture 11 shows the complete assembly for this issue.

Markwarren attached the following image(s):
20 (1).jpg
20 (2).jpg
20 (3).jpg
20 (4).jpg
20 (5).jpg
20 (6).jpg
20 (7).jpg
20 (8).jpg
20 (9).jpg
20 (10).jpg
20 (11).jpg
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.485 seconds.
DeAgostini