|
|
 Rank: Super-Elite        Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,103 Points: 15,458 Location: ipswich
|
STAGE 43:
Right front wheel.
Pic 1: Immerse the tyre 43A in a bowl of hot water for around two minutes.
Take care here.
Pic 2: Remove the tyre from the hot water using tongs.
Pic 3: Dry the tyre inside and out and lay it on a firm surface.
Place the wheel 43B on top of the tyre.
Pic 4: Press firmly down on the wheel so that it goes into the tyre.
Pic 5: Shows the wheel with the tyre fitted.
Pic 6: Retrieve the main car assembly and the front brake disc 41L from stage 41.
Locate the washer 43C and screw DM.
Pic 7: Fit the disc to the hub and fix with the DM screw through the washer 43C.
Pic 8: The printed instructions suggest fitting the wheel to the car now using 4 x AM screws.
The wheel will be fitted near the end of the build due to the extra weight on the assembly at this stage could cause problems due to constantly turning the model upside down and back again during future stages of the build.
This is entirely at the builder’s discretion.
Pic 9: If you do not fit the wheel, save it and the labelled fixing screws safely.roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,103 Points: 15,458 Location: ipswich
|
STAGE 44A:
Spare wheel bracket.
Pic 1: Fit the small bracket 44B onto the main wheel bracket 44A as shown and fix from behind with 1 x AM screw.
Pic 2: Stick three of the self-adhesive pads 44G onto the strap 44E in the positions shown.
Pic 3: Feed one end of the strap through the loop on the bracket 44A as shown.
Peel off the backing paper from the adhesive pad and fold the strap over to secure it.
The adhesive pads are not very secure so you may wish to use a dot of adhesive here.
This is entirely at the builder’s discretion.
Pic 4: Close up of the strap join.
Pic 5: Feed the metal loop 44F onto the strap as shown.
Pic 6: Fit the other end of the strap to the main frame in the same way, as shown.
The adhesive pads are not very secure so you may wish to use a dot of adhesive here.
This is entirely at the builder’s discretion.
Pic 7: Holding the metal loop 44F in place, squeeze the strap together after removing the backing paper from the adhesive pad.
As before, the adhesive pads are not very secure so you may wish to use a dot of adhesive here.
This is entirely at the builder’s discretion.
Pic 8: Close up of the strap and loop join.roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,103 Points: 15,458 Location: ipswich
|
STAGE 44B:
Pic 9: Locate the bracket 44C (Left) and fit it to the main frame as shown.
Pic 10: Locate the bracket 44D (Right) and fit it to the other end of the main frame as shown.
Pic 11: Retrieve the main car assembly and turn it so the engine is towards you.
Make sure the arms 15B and 15C are laying down as shown.
Pic 12: Fit the tyre bracket assembly to the lower rear of the engine frame as shown with the bracket 44C(L) locating in the slots on the inside of the engine frame.
Fix from the other side with 1 x AM screw.
Pic 13: Fit the other end of the tyre bracket assembly to the lower rear of the engine frame as shown with the bracket 44D(Right) locating in the slots on the inside of the engine frame.
Fix from the other side with 1 x AM screw.
Pic 14: Fit the arm 15C into the bracket 44B and fix using 1 x BM screw.
Pic 15: Fit the other bracket 15B to the tyre bracket 44A and fix with 1 x SP screw.
Pic 16: Store the model safely for now.roymattblack attached the following image(s):
|
|
|
|
Guest
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
US
