|
|
 Rank: Super-Elite        Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,302 Points: 16,058 Location: ipswich
|
STAGE 57A:
Driver’s seat and harness.
Pic 1: Retrieve the floor and seat from the previous stage and fit the strap through the seat base.
Pic 2: Different view.
Pic 3: Fit the seat base 57A in place as shown with the longer tabs to the front and fix with 2 x XP screws in each side.
Pic 4: Fix the seat to the floor with 2 x AP screws.
Pic 5: Repeat on the other side.
roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,302 Points: 16,058 Location: ipswich
|
STAGE 57B:
Pic 6: Cut one end of the strap 57C to the shape as shown.
Pic 7: Carefully burn the end to seal it.
NOTE: An easier and safer way is to dip the end of the strap in a tiny dot of cyano glue and allow it to dry before cutting the shape.
This is entirely at the builder’s discretion.
Pic 8: Pass the strap through the bracket 57B (smaller bracket) as shown and stick a piece of double sided tape to the large end of the strap.
Pic 9: Peel the backing from the tape and fold it over the bracket.
Pic 10: Fit a catch 57D to the narrow end of the strap and using a piece of tape, fold it over in the same way.
Make another strap in the same way so you have two sets the same.
Pic 11: Using parts 57D, 57F, 57H and 57K, make two more sets of straps using the same method.
Pic 12: Straps assembled.roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,302 Points: 16,058 Location: ipswich
|
STAGE 57C:
Pic 13: Lay a long strap 57G face down so the ‘Sabelt’ name is underneath and fit a large bracket 57E in place as shown.
The ‘S’ in Sabelt must be nearest to the bracket or the name will be upside down when finished.
Stick a piece of tape 57K as shown.
Pic 14: Fold the end of the strap over as with the other belts.
Pic 15: Retrieve strap 57F and pass the end of the new strap through the bracket 57H where indicated.
Pic 16: Again using the tape method, fold the end of the strap over and fix it in place.
Pic 17: Completed strap.
Note the direction of the name.
Pic 18: Make another set the same.
Pic 19: Fit one of the straps 57C through the side of the seat.
Pic 20: Fit the bracket to the floor and fix from underneath with 1 x AP screw.roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,302 Points: 16,058 Location: ipswich
|
STAGE 57D:
Pic 21: Repeat with the other strap on the other side.
Pic 22: Fit the two long straps through the upper holes in the seat back.
It will be far easier to fit them from behind.
Pic 23: Locate the strap lock back 57J and fit the ends of the three lower straps in place as shown.
This VERY fiddly so be patient.
Pic 24: Fit the two upper straps in the same way.
Pic 25: Press-fit the front lock 57I into the central hole to fix everything together.
Store the assembly safely for now.
roymattblack attached the following image(s):
|
|
|
|
Guest
|
US
