|
|
 Rank: Super-Elite        Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,346 Points: 16,190 Location: ipswich
|
STAGE 15:
Left rear swing arm.
Pic 1: Locate the arm 15-2, bracket, 15-3 and screw ‘F’.
The parts fit together in the order shown.
Pic 2: Parts assembled.
Pic 3: Locate the arm 15-1, 2 x brackets, 15-3 and 2 x screws ‘F’.
The parts fit together in the order shown.
Pic 4: Parts assembled.
Pic 5: Retrieve the assembly from stage 14 and fit the arm 15-2 as shown.
Fix using 1 x ‘G’ screw.
Pic 6: Fit the other arm 15-1 to the other end of the hub, between the springs and fix with 1 x ‘G’ screw.
Pic 7: Shows the arm fitted (highlighted in yellow) from a different angle for clarity.
Store the assembly safely.roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,346 Points: 16,190 Location: ipswich
|
STAGE 16:
Rear frame.
Pic 1: Fit the 2 x suspension bases 16-2 to the top of the frame 16-1 as shown and fix with 2 x ‘D’ screws in each.
Pic 2: Retrieve the hub assembly from the previous stage and fit it against the frame as shown.
The 4 x flexible brackets on the ends of the swing arms locate in the 4 x recesses on the frame.
This is quite fiddly so it is suggested you fix them as follows:
Pic 3: Position the arm 14-A first, ignoring the other three fixings for now.
Fix with 1 x ‘G’ screw.
Then position the end of arm 15-2, and fix with 1 x ‘G’ screw.
Pic 4: Position the ends of the ‘A’ shaped arm 15-1 in the locating holes and fix with 2 x ‘G’ screws.
Pic 5: From the other side, fix the tops of the dampers using 4 x ‘R’ screws.
Store the assembly safely.roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,346 Points: 16,190 Location: ipswich
|
STAGE 17:
Right rear suspension.
NOTE: Steps 1 and 2 are missing from the printed instructions which only describe step 3 (pic 4 below) but they are detailed here.
Pic 1: Locate the lower arm 17-3 and bracket 17-4.
You will also need 1 x screw ‘F’.
The parts fit together in the order shown.
Pic 2: Parts assembled.
Pic 3: Fit the assembly to the bottom of 17-2, between the silver forks as shown.
Fix with 1 x ‘F’ screw.
Pic 4: Fit the hub 17-1 to the lower arm just fitted to the assembly and fix from below with 1 x ‘G’ screw.
Store safely for now.
roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,346 Points: 16,190 Location: ipswich
|
STAGE 18:
Right rear brake.
Pic 1: Retrieve the assembly from the previous stage and fit the caliper 18-6 as shown.
Fix from behind with 1 x ‘A’ screw.
Pic 2: Press-fit the backing plate 18-4 into place.
It will only fit one way.
Pic 3: Locate the disc parts 18-1 and 18-2.
They will fit together one on top of the other.
Pic 4: Wit the parts together, peel the backing from the steel disc face 18-3 and stick it in place as shown.
Pic 5: Fit the disc centre 18-5 in place and fix from behind with 2 x ‘I’ screws.
Pic 6: Store everything safely for now.
roymattblack attached the following image(s):
|
|
|
|
Guest (3)
|
US
