|
|
 Rank: Super-Elite        Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,371 Points: 16,265 Location: ipswich
|
STAGE 69A:
Dashboard and roll cage.
Pic 1: Retrieve the dashboard from the last stage and fit the control panel 69B as shown.
Fix from behind with 2 x AP screws.
Pic 2: Repeat using the panel 69C and 2 x AP screws.
Pic 3: Fit the third panel 69D and fix from behind with 1 x AP screw.
Pic 4: From behind, fit the gauge panel 69E as shown.
Pic 5: Fix the bracket 69F over the gauges with 2 x AP screws.
Pic 6: Press-fit the control stalks 69G and 69O into the locating holes in the dashboard where shown.
Pic 7: Press-fit the two switches 69I in place where shown.
roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,371 Points: 16,265 Location: ipswich
|
STAGE 69B:
Pic 8: Fit the 3 x control boxes 69H and 1 x 69P in place where indicated.
Pic 9: Fit two more switches 69I where shown.
Fit the switches 69L and 69J where indicated.
Pic 10: Retrieve the front panel assembly from the previous stage and fit the dashboard in place as shown.
Pic 11: Fix from the other side with 3 x AP screws.
Pic 12: The assembled dashboard.
Pic 13: Fit the top panel 69A in place.
Pic 14: Fix from underneath with 3 x AP screws.
roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,371 Points: 16,265 Location: ipswich
|
STAGE 69C:
Pic 15: Retrieve the interior assembly and locate the 2 x 65N cables.
Pass them out of the front.
Pic 16: Fit the dashboard assembly in place with the two cables passing through the small rectangular opening.
Fix the parts with 3 x AP screws.
Pic 17: Retrieve the roll cage assembly and fit it in place as indicated.
Pic 18: Fix the rear legs of the roll cage to the back panel using 1 x AP screw from underneath in each leg.
Pic 19: Position the front leg of the roll cage behind the upright panel as shown and fix with 1 x AP screw from underneath and two more screws through the upright panel.
Pic 20: Repeat on the other side.
Pic 21: Gather the 4 x wires on the control box at the rear and pass them out of the back of the roll cage.
Fix them in place as shown using the cable tie 69N as shown.
Pic 22: Cut the excess off the cable tie and rotate it so it is not so easily seen.
Store the assembly safely.roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,371 Points: 16,265 Location: ipswich
|
STAGE 70:
Lower left fuel tank.
Pic 1: Cut the wire 70E into 5 x 60mm pieces.
Pic 2: Position the mesh 64H at the rear of the roll cage as shown, in an ‘L’ shape.
Using the 5 x wires, fasten the mash at the upper edge to the roll cage where indicated, twisting the wires to secure them.
Pic 3: Cut off the excess wire.
Pic 4: Retrieve the main car assembly and place it upside down.
Fit the fuel tank part 70B in place as shown.
Pic 5: From the other side, fix the tank using 4 x AP screws where indicated.
Pic 6: Fit the fuel pipe 70C into the slot at the end of the tank part 70A.
Pic 7: Fix the cover 70D in place with 2 x AP screws.
Store everything safely for now. roymattblack attached the following image(s):
|
|
|
|
Guest (3)
|
US
