|
|
Rank: Administration         Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds Joined: 04/01/2016 Posts: 7,086 Points: 21,565 Location: Northamptonshire, England
|
Issue 15
Picture 1 shows the parts for this issue.
Put the clutch plate (15A) and clutch bell (15B) together as shown in pictures 2 and 3. Retrieve the engine cover from the last issue and place the clutch assembly onto the engine cover securing it using a TP screw as illustrated in pictures 4 and 5.
Now attach the clutch flange (15C) to the clutch and cover assembly as shown in picture 6. Turn the assembly over and secure in place using 2 x BP screws, picture 7.
The cover is secured to the engine with a total of 14 screws. Begin by tightening 4 x AM screws as shown in picture 8. Finish off the assembly by attaching 10 x BP screws as illustrated in picture 9.
Picture 10 shows the complete assembly for this issue.
Markwarren attached the following image(s): Regards
Markwarren
(Mark) Admin
|
|
|
Rank: Administration Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds Joined: 04/01/2016 Posts: 7,086 Points: 21,565 Location: Northamptonshire, England
|
Issue 16
Picture 1 shows the parts for this issue.
Fit the oil pump flange (16F) onto the transmission cover (16A) and secure it in place using a KP screw. Fit the oil pump (16C) and bring it over the oil flange, picture 2. Secure it in place using a KP screw, picture 3.
Fit the chain guard (16E) in place securing it with 2 x KP screws, picture 4.
Retrieve the engine assembly and fit the transmission cover securing it place using 4 x AM screws, picture 5.
Take the lock washer (16C) and place the sprocket nut (16D) as shown in picture 6. Take the sprocket (16B) and mount it onto the drive shaft as shown in picture 7. Next, put the washer nut assembly into the sprocket and push into the drive shaft, picture 8. Take the DM flanged screw and secure it in place, picture 9.
Picture 10 shows the complete assembly for this issue.
Markwarren attached the following image(s): Regards
Markwarren
(Mark) Admin
|
|
|
Rank: Administration Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds Joined: 04/01/2016 Posts: 7,086 Points: 21,565 Location: Northamptonshire, England
|
Issue 17
Picture 1 shows the parts for this issue.
Assemble the cover (17A) and the rod (17B) together as shown in pictures 2 and 3. Secure them both using an AP screw, picture 4.
Retrieve the engine and place the assembly to the engines left side, securing it in place using 2 x AM screws, pictures 5 and 6.
Place the phonic disk (17C) and orientate it as shown in picture 7. Finally, place the nut (17D) and push fit it into place, picture 8.
Picture 9 shows the complete assembly for this issue.
Markwarren attached the following image(s): Regards
Markwarren
(Mark) Admin
|
|
|
Rank: Administration Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds Joined: 04/01/2016 Posts: 7,086 Points: 21,565 Location: Northamptonshire, England
|
Issue 18
Picture 1 shows the parts for this issue.
Place the exhaust connector (18C) to the exhaust manifold section (18B), picture 2. Secure it in place using an AP screw, picture 3. Take the exhaust manifold (18A) and attach it to the other half, picture 4.
Pictures 5 and 6 show the complete assembly for this issue.
Markwarren attached the following image(s): Regards
Markwarren
(Mark) Admin
|
|
|
|
Guest
|
US
