|
|
 Rank: Super-Elite        Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,434 Points: 16,454 Location: ipswich
|
STAGE 75:
Front trunk floor.
Pic 1: Push the hose 75C onto the small pin on the fitting 75B.
Pic 2: The fitting attaches to the floor 75A where shown.
Pic 3: Fix from the other side with 1 x NP screw.
Pic 4: Store the assembly safely for now.
roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,434 Points: 16,454 Location: ipswich
|
STAGE 76A:
Fuel filler pipes.
Pic 1: Locate the pipe parts 76A, 76B, 76C and 76D.
Pic 2: Press-fit the parts together as shown.
Pipe 76AB should have TWO fitting holes at the top – one on each side.
Pipe 76C/D only has one, on one side.
Pic 3: Fit the black connector 76I into the hole in pipe half 76B.
Pic 4: Fit the connector 76E into the hole in the other side, on pipe half 76A.
This fuel pipe will have TWO connectors. One black, one silver.
Pic 5: Fit the connector 76E into the hole on pipe half 76C as shown.
This fuel pipe will only have ONE connector.
Pic 6: Assemble the 2 x filler caps with parts 2 x 76H, 2x 76G and screws 2 x LP as shown.
Pic 7: OPTIONAL ADDED DETAIL – You can colour the inside of the fuel cap parts with black paint or a Sharpie to represent the ‘hole’.
This is at the builder’s discretion.roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,434 Points: 16,454 Location: ipswich
|
STAGE 76B:
Pic 8: Fit the funnels – 2 x 76F to the fuel pipes and then fix the filler caps with 1 x AP screw through the centre of each as shown.
Pic 9: Cut the tube 76M into three parts.
2 x 45mm, 1 x 65mm.
Pic 10: Fit the tubes to the fuel pipes as shown.
Pic 11: Locate the strap parts 76J, 76K and 76L.
Stick 1 x 76L to the strap where shown.
Pic 12: Fit the buckle 76J to the strap.
Peel the backing from 76L and fold the strap over as shown.
Pic 13: Retrieve the panel 74A and stick 76L to the outer curve under the small slot.
Pic 14: From the other side, feed the strap through the slot where indicated.
Pic 15: Peel the backing from 76L and stick the end of the strap firmly in place.
Pic 16: Store all parts safely for now.roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,434 Points: 16,454 Location: ipswich
|
STAGE 77:
Radiator and fans.
Pic 1: Fit the 3 x fans 77C onto the radiator 77A as shown.
They will only fit one way.
Fix with 3 x TP screws.
Pic 2: Locate the fan guard 77B and the 3 x covers 77D.
The covers will press-fit to the guard.
Make sure they are fitted the correct way up as shown.
Pic 3: Parts assembled.
Pic 4: Fit the assembly to the radiator and fix with 6 x AP screws where indicated.
Store the parts safely for now.
roymattblack attached the following image(s):
|
|
|
|
Guest
|
US
