|
|
 Rank: Super-Elite        Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,519 Points: 16,709 Location: ipswich
|
STAGE 81:
Driver’s seat.
Pic 1: Twist the end of the buckle 81C at right-angles as shown.
Pic 2: Fix an adhesive tab 81B to one end of the strap 81D.
Slide the buckle 81C onto the strap as indicated.
Pic 3: Peel the backing from the tab and fold the strap over the buckle.
Pic 4: Fix another tab 81B to the other end of the strap.
Pic 5: Feed the strap through the slot in the base of the seat 81A.
Pic 6: Turn the seat over, remove the backing from the tab and stick the strap down where indicated.
Pic 7: Store safely for now.
roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,519 Points: 16,709 Location: ipswich
|
STAGE 82:
Driver’s seat 2.
Pic 1: Fit the support bracket 82F to the back of the seat panel 82A as shown and fix from the other side with 2 x XP screws.
Pic 2: Fit the seat face 81A from the previous stage.
Pic 3: Check that the top tabs fit over the frame where indicated.
Pic 4: Fix the seat parts together with 3 x TP screws.
Make sure the lower tab is located properly where shown.
Pic 5: Fix the other side together with 3 x TP screws.
Make sure the lower tab is located properly where shown.
Pic 6: Fix the lower front with 3 x TP screws.
Pic 7: Fit the head protection brackets 82B and 82E as indicated and fix with 1 x TP screw in each.
Pic 8: Fit the head protection pads 82C and 82D where shown.
Pic 9: Store the seat for now.
roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,519 Points: 16,709 Location: ipswich
|
STAGE 83:
Driver’s seat 3.
Pic 1: Fit the side supports 83B and 83C to the seat back where shown and fix with 2 x TP screws in each.
Pic 2: Slide the support pads 83A and 83D over the supports as shown.
The text goes to the outside, upwards.
Pic 3: Store safely for now.
roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,519 Points: 16,709 Location: ipswich
|
STAGE 84:
Driver’s seat 4.
Pic 1: Fix the support bracket 84A to the base of the seat 82A using 2 x AM screws.
Pic 2: Fix the rear support 82C to the base of the seat as shown using 2 x EP screws.
Pic 3: gently flex the frame 84B so you can fit the seat between the side rails.
Pay attention to the orientation of the seat and frame.
Fix on one side with 2 x FM screws.
Pic 4: Fix the other side in the same way with 2 x FM screws.
Store the seat safely for now.
roymattblack attached the following image(s):
|
|
|
|
Guest
|
US
