|
|
 Rank: Super-Elite        Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,571 Points: 16,865 Location: ipswich
|
STAGE 93:
Front right bulkhead.
Pic 1: Press-fit the tank part 93B into the bulkhead 93A as shown.
Pic 2: Turn the bulkhead over and position the pipe 93F where indicated and fix in place with 2 x brackets 93G and 2 x MP screws in each.
Pic 3: Press-fit the drain hose 93C in place.
Pic 4: Turn the main car assembly upside down and make sure all the wires indicated are out of the way.
Pic 5: Fit the bulkhead in place as shown and fix with 2 x AM screws.
Make sure the drain hose is located in the hole where indicated.
Pic 6: With the car the right way up, fit the ends of the pipe shown into the locating holes highlighted.
Pic 7: As before, you can now fit the front wheel if you wish.
Retrieve the brake disc 36C/D and fit it over the stub axle.
Fit the wheel over the disc and then add the central washer 93E.
Fix the wheel with 1 x FM screw.
Pic 8: Fit the centre spinner 37D.
Store the model and unused parts safely for now.roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,571 Points: 16,865 Location: ipswich
|
STAGE 94:
Lower left body.
Pic 1: Retrieve the car assembly and fit the on/off switch (wire A) into the location hole on the inside of the lower panel 94A.
Fix with 2 x AGM screws.
Pic 2: Remove the rear panel for now and do not lose the screws.
Pic 3: Panel removed.
Pic 4: Very carefully turn the model over.
Pic 5: Fit the lower panel place making sure the switch wire goes all the way back inside the body so it does not get trapped anywhere.
Fix the panel in place with 5 x TM screws.
Pic 6: Looking down inside the rear of the body, fit 1 x ATM screw in the locating hole as shown.
You will need a fairly long screwdriver for this and be patient.
It is quite fiddly.
Pic 7: re-fit the rear panel.
Pic 8: Clip the battery cover from stage 92 in place.
Pic 9: With the model the right way up, fit 1 x TM screw where shown.
Pic 10: Cut one of the decals 94B from the supplied sheet. There is a spare.
Soak in warm water for about 15 seconds and then slide the decal into place.
Dab it down with a folded tissue or kitchen roll.
Store the model safely.roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,571 Points: 16,865 Location: ipswich
|
STAGE 95:
Lower right body.
Pic 1: Retrieve the car assembly and place it upside down.
As before, remove the rear panel and keep the screws.
Pic 2: Position the lower body panel in place.
Looking down inside the rear of the body, fit 1 x ATM screw in the locating hole as shown.
You will need a fairly long screwdriver for this and be patient.
It is quite fiddly.
After this, re-fit the panel.
Pic 3: Check the lower panel is not trapping any wires anywhere anywhere.
Fix the panel in place with 5 x TM screws.
Pic 4: With the model the right way up, fit 1 x TM screw where shown.
Pic 5: If you wish, you can now fit the rear wheel using the brake disc, washer and supplied screw.
Pic 6: Store the model safely.
roymattblack attached the following image(s):
|
|
|
|
Guest
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
US
