|
|
 Rank: Super-Elite        Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,584 Points: 16,904 Location: ipswich
|
STAGE 87:
Steering column.
Pic 1: Retrieve the steering wheel and remove the centre cap.
Pic 2: Fit the shaft 87D into the back of the wheel.
Note that one end has a shorter stepped part. This fits in the wheel.
Fix from the front with 1 x AM screw.
Pic 3: Re-fit the centre cap.
Pic 4: Fit the driver’s intercom as shown.
The part is not a tight fit so you may wish to use a little adhesive.
This is at the builder’s discretion.
Pic 5: Locate the column parts 87A and 87B.
They fit together, one on top of the other.
Pic 6: Fix using 4 x AP screws.
Pic 7: Peel the backing from the felt sheet 87C and wrap it around the black section of the column as shown.
Store everything safely for now.roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,584 Points: 16,904 Location: ipswich
|
STAGE 88:
Dashboard and firewall.
Pic 1: Retrieve the interior and firewall assemblies.
Fit the firewall behind the locating tabs on the interior and fix the parts with 5 x EP screws.
Pic 2: Connect the 3 x ignition wires as shown.
The printed instructions say to pass the short lead through a hole in the firewall.
There is no hole – the wire connects to a pin.
Pic 3: Store the assembly and unused part safely.
roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,584 Points: 16,904 Location: ipswich
|
STAGE 89:
Dashboard brace.
Pic 1: Retrieve the dashboard from stage 88 and fit one of the ‘L’ shaped brackets 89C as shown.
Fix with 1 x EP screw.
The bracket will only fit one way.
Pic 2: Repeat on the other side.
Pic 3: Retrieve the column housing 87A and fit the larger bracket 89B as shown.
Fix with 2 x AP screws.
Pic 4: Fit the column housing onto the brace 89A as shown.
Pic 5: Fix from underneath with 2 x CM screws.
Pic 6: Store safely for now.
roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,584 Points: 16,904 Location: ipswich
|
STAGE 90:
Dashboard front panel.
Pic 1: Fit the 6 x dashboard lenses 5 x 90E and 1 x 90D in the order as shown.
Pic 2: Fit the instrument panel 90C over the top.
Pic 3: View from the other side.
Pic 4: Retrieve the main assembly and remove the screw and bracket indicated.
Keep the parts safe for later use.
Pic 5: Unplug the LED strip as shown.
Pic 6: Peel the backing paper from the LED strip and stick it to the dashboard front where shown.
Pic 7: Fit the dash panel 90B over the LED strip.
Pic 8: Fix from behind with 2 x QP screws.
Pic 9: Reconnect the plug and socket.
Store everything safely for now.
roymattblack attached the following image(s):
|
|
|
|
Guest (2)
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
US
