|
|
 Rank: Super-Elite        Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,622 Points: 17,018 Location: ipswich
|
STAGE 99A:
Front body and air intakes
.
Pic 1: Retrieve the front body and place it upside down.
Tape the light cables down as shown.
Pic 2: Fit the air intake frame 99A and fix with 3 x AM screws.
Pic 3: Fit the left brake hose manifold 99B as shown and fix with 2 x AM screws.
Pic 4: Fit the right brake hose manifold 99C as shown and fix with 2 x AM screws.
Pic 5: Press-fit the inner brackets 99E and 99F in place where indicated.
Pic 6: Fit the air intake cover 99D in place.
roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,622 Points: 17,018 Location: ipswich
|
STAGE 99B:
Pic 7: Gather the light cables and tie them using the cable tie 99G.
Cut off the excess afterwards.
Pic 8: Retrieve the main body.
Gather the light cables and tie them using the cable tie 99G.
Cut off the excess afterwards.
Pic 9: Position the front body as shown and connect all the wires and plugs.
Take care to connect the matching letters.
Pic 10: Turn the body panel over and fit it in place.
Fix using 6 x TM screws and 2 x AKP screws.
Pic 11: Fix the lower body with 1 x AUM screw.
Repeat on the other side.
Pic 12: Fit the light cover 98K as shown and fix with 2 x MM screws.
Pic 13: Fit the light cover 98L as shown and fix with 2 x MM screws.
Store the model safely for now.
roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,622 Points: 17,018 Location: ipswich
|
STAGE 100:
Lower front body.
Pic 1: Soak one of the supplied decals 100F in warm water for about 10 seconds and then slide the decal into place as shown.
Dab with a folded tissue or paper towel and allow to dry.
Pic 2: Locate the extension 100D. It fits on the right side of the panel 100A.
It can be identified by the pin on the lower side.
Fix in place with 2 x AM screws.
Pic 3: Locate the extension 100B. It fits on the left side of the panel 100A.
It can be identified by the pin on the lower side.
Fix in place with 2 x AM screws.
Pic 4: Locate the brackets 100C and 100E.
They can be identified by the letters ‘L’ and ‘R’ on each part.
Pic 5: With the panel 100A facing up, fit the bracket 100C as shown.
It has been outlined to make it show more clearly.
Pic 6: With the panel 100A facing up, fit the bracket 100E as shown.
Pic 7: Turn the car assembly upside down and fit the front panel as shown.
It will slide under the black brackets and two pins inside will locate in holes in the panel.
Fix with 3 x AM screws.
Pic 8: Store the model safely.
roymattblack attached the following image(s):
|
|
|
|
Guest
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
US
