|
|
Rank: Administration         Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds Joined: 04/01/2016 Posts: 7,271 Points: 22,120 Location: Northamptonshire, England
|
Issue 104
Picture 1 shows the contents of this issue.
Hood Inner Reinforcement.
Place the hood latch 104 B on the outside of the hood in a reinforcement 104 A. Note there is only one way this will mount as the latch has one side longer than the other. Turn the assembly over and secure it in place using a PS31 screw as shown in pictures 2 and 3.
That completes the assembly for this issue.
Markwarren attached the following image(s): Regards
Markwarren
(Mark) Admin
|
|
|
Rank: Administration Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds Joined: 04/01/2016 Posts: 7,271 Points: 22,120 Location: Northamptonshire, England
|
Issue 105
Picture 1 shows the contents of this issue.
Hood
Place the inner reinforcement on the underside of the hood and make sure that the four protrusions on the hood fit snugly into the holes in the reinforcement. Fix the reinforcement to the hood with four DS35 screws as shown in picture 2.
That completes the assembly for this issue.
Markwarren attached the following image(s): Regards
Markwarren
(Mark) Admin
|
|
|
Rank: Administration Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds Joined: 04/01/2016 Posts: 7,271 Points: 22,120 Location: Northamptonshire, England
|
Issue 106
Picture 1 shows the contents of this issue.
Left Front Fender
Separate this sticker with the emblem (106C) from its backing. Attach the sticker to the emblem base (106B), picture 2. Now attach the emblem to the rear side of the left front fender as shown in picture 3.
Turn the assembly over and fix the base with a PS17 screw from the inside, picture 4.
Pictures 5 shows the final assembly for this issue.
Markwarren attached the following image(s): Regards
Markwarren
(Mark) Admin
|
|
|
Rank: Administration Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds Joined: 04/01/2016 Posts: 7,271 Points: 22,120 Location: Northamptonshire, England
|
Issue 107
Picture 1 shows the contents of this issue.
Chassis Front Panel
Place the right hood support (107C) identified with an R on its base, on the outer face of the chassis front panel (107A). Push the thin pin into the front panel, picture 2, then turn the front panel over and secure the support using a PS08 screw as shown in picture 3.
Repeat the previous step and place the left hood support 107B, identified with an L on its base, picture 4.
That completes the assembly for this issue.Markwarren attached the following image(s): Regards
Markwarren
(Mark) Admin
|
|
|
Rank: Administration Groups: Registered, Administrators, Global Forum Support, Moderator, Forum Support Team, Official Builds Joined: 04/01/2016 Posts: 7,271 Points: 22,120 Location: Northamptonshire, England
|
Issue 108
Picture 1 shows the contents of this issue.
Right Front Fender
As you did in issue 105, attach the emblem base (108B) to the rear of the right front Fender (108A), picture 2.
Retrieve the chassis front panel. Put it alongside the right front Fender so you can see where the two parts are attached, picture 3. Fix the panel to the Fender using 2DS10 screws through the front of the assembly as shown in picture 4.
Now retrieve the left front Fender and position it in the same way as the right front Fender. Secure it in place using two DS10 screws, picture 5.
That completes the assembly for this issue.
Markwarren attached the following image(s): Regards
Markwarren
(Mark) Admin
|
|
|
|
Guest
|
US
