|
|
 Rank: Super-Elite        Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,707 Points: 17,273 Location: ipswich
|
STAGE 87A:
Roof interior.
Pic 1: Fix the large panel 87E to the roof lining with 2 x GP screws underneath.
Pic 2: Fix the 2 x smaller panels 87F with 1 x GP screw in each from underneath.
Pic 3: Fix the black box 87G with 1 x BP screw underneath.
Pic 4: Fit the left sun visor 87C as shown.
Pic 5: Fit the hinge pin 87B where indicated.
Pic 6: Fix the retainer 87A (L) with 2 x IP screws.
Pic 7: Repeat on the other side with the right hand parts.
roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,707 Points: 17,273 Location: ipswich
|
STAGE 87B:
Pic 8: Fit the 3 x LED’s 87I on the inside of the roof lining as shown.
The black tape 87J over the central LED is to hold it in place as it is a very loose fit.
Pic 9: Fix tapes 87J over all of the LED’s.
Pic 10: Fix the wires at the rear of the roof lining using the tab 87H and 1 x IP screw.
Pic 11: Feed the 2 x LED’S on wire 87K through the holes in the car roof where shown.
Pic 12: On the outside, tape the LED’s down with 2 x 87J.
Pic 13: On the inside of the car, secure all of the wires out of the way at the rear.
Pic 14: Fit the roof lining in place and fix with 6 x NM screws.
Pic 15: Fix the front screen pillars with 2 x BM screws.
Store safely for now.roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,707 Points: 17,273 Location: ipswich
|
STAGE 88:
Interior panels.
Pic 1: Locate the seat belts 88A (L) and 88D (R).
The brackets are marked so you can identify them.
Pic 2: Fix 88A to the side panel 88B with 1 x IP screw from behind.
Pic 3: Fix 88D to the side panel 88E with 1 x IP screw from behind.
Pic 4: Retrieve the car body and place it upside down.
Fit panel 88B in place, hooking the roof end under the roof panel, and fixing at the bottom with 1 x DM screw.
Pic 5: Fit panel 88E in place, hooking the roof end under the roof panel, and fixing at the bottom with 1 x DM screw.
Pic 6: Fix the front panel 88F with 2 x DM screws.
Pic 7: Fix the front panel 88C with 2 x DM screws.
Pic 8: Open the driver’s door and fix the inner panel with 1 x FP screw where shown.
Pic 9: Repeat on the other side.
Store safely for now.
roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,707 Points: 17,273 Location: ipswich
|
STAGE 89:
Engine cover.
Pic 1: Fix the 2 x hinges 89B to the rear of the engine cover as shown using 2 x QM screws in each.
Store safely for now.
roymattblack attached the following image(s):
|
|
|
Rank: Super-Elite Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered Joined: 04/06/2011 Posts: 5,707 Points: 17,273 Location: ipswich
|
STAGE 90:
Engine cover.
Pic 1: Fit the catch 90D and spring 90E together as shown.
Pic 2: Retrieve the engine cover and fit the assembly into the locating slot as shown and fix with the bracket 90F and 2 x QM screws.
Pic 3: Fit the cover stay 90A and 90B together as shown.
Pic 4: Add the fixing bracket 90C.
Pic 5: Retrieve the main body and place it upside down.
Fix the retaining bracket 90C to the rear wall of the engine bay as shown using 2 x AP screws.
Pic 6: Turn the body the right way up and fix the engine cover in place with 2 x QM screws in each hinge.
Pic 7: Again with the body upside down, fit the cover stay long bracket 90A to the inside of the engine cover with 1 x QM screw.
Pic 8: Fix the hoses 90G and 90H together with 1 x AP screw.
Pic 9: Fix the tee-pipe 90I to the assembly with 1 x AP screw.
The parts will only fit one way.
Store safely for now. roymattblack attached the following image(s):
|
|
|
|
Guest (2)
|
US
