|
|
 Rank: Pro  Groups: Registered
Joined: 30/08/2012 Posts: 336 Points: 857 Location: London
|
Mr T's build seem to differ slightly from the mag so I want to double check. Exactly which pins remain when glue has dried?
Is it the first and last of each strip or just the final 3 frames of the stern?
|
|
|
Rank: Pro Groups: Joined: 24/08/2009 Posts: 48,827 Points: -13,348
|
Where the strips butt and the last three frames..
|
|
|
Rank: Pro Groups: Registered
Joined: 30/08/2012 Posts: 336 Points: 857 Location: London
|
Thanks. Is it normal to have to predrill the planks? The pins are just bending when pushed.
|
|
|
|
|
With bamboo other builders have found pre drilling a must to prevent the bamboo splitting, as for the pins bending they will bend in any wood if you don't push them in straight every time, with practice u will bend less . Hope this helps Andy Current builds:-C57,Zero, Lamborghini Countach, Caldercraft HMS Agamemnon,Robi,R2-D2, MFH Cobra .
|
|
|
|
|
Rob, I have found it a must to predrill with a .5mm drill... Helps to stop the bamboo splitting and it also helps to stop the pins bending.... I don't use a pin pusher, I use long nose pliers to push the pin into the predrilled hole just far enough to take hold then use a small hammer to finish..... Couldn't take to a pin pusher.... you will soon find you own method.... Good luck...
Regards
Alan
|
|
|
Rank: Pro Groups: Registered
Joined: 30/08/2012 Posts: 336 Points: 857 Location: London
|
Cheers.
It gets to a point where i'm pushing so hard i'm worried it's going to break the ship.
However, drilling all them holes by hand seems a very long task. I wonder if it's possible to buy small adaptors, so I can use a drill bit with my small electric screwdriver.
|
|
|
Rank: Pro Groups: Registered
Joined: 22/06/2010 Posts: 179 Points: 428 Location: Poole Dorset
|
Hi Rob, Do a search for a "hex drill chuck" you will find plenty on e-bay and Amazon. I bought one quite recently. Check to see what the smallest size bit they take. cheers Peter completed..... Endeavour Longboat, San Francisco 2, Virginia 1819
building Royal Caroline
|
|
|
Rank: Administration       Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,252 Points: 23,844 Location: East midlands
|
catman275 wrote:Hi Rob,
Do a search for a "hex drill chuck" you will find plenty on e-bay and Amazon. I bought one quite recently.
Check to see what the smallest size bit they take.
cheers Peter
Hi Rob Take a look at this one on ebay Item number: (250890099448) Takes drill bits from 0 - 0.85mm Regards Delboy271155 (Derek) COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
|
|
|
|
|
Hi RobT Personally I prefer to use a pin vice (see below) its much more controllable than a power drill and less likely to 'skid' across the planks. The handle breaks down into three sections with a selection of different chucks inside. Most model shops will have them or try ebay and Hobby's Annual, roughly a fiver or so in cost. Robin Plymouth57 attached the following image(s): First wooden ship: The Grimsby 12 Gun 'Frigate' by Constructo Second: Bounty DelPrado Part Works Third: HMS Victory DelPrado Part Works 1/100 scale Diorama of the Battle of the Brandywine from the American Revolutionary War Diorama of the Battle of New Falkland (unfinished sci-fi), Great War Centenary Diorama of the Messines Ridge Assault Index for the Victory diary is on page 1
|
|
|
Rank: Pro Groups: Registered
Joined: 30/08/2012 Posts: 336 Points: 857 Location: London
|
I have one but for the life of me I cant get it to grab the drill bits properly.
Anyway, I went to B&Q. I found something called a Dremel multi chuck which does the job superbly. Obviously not on my screwdriver, but on my Dremel. Like a knife through butter.
|
|
|
Rank: Pro Groups: Joined: 24/08/2009 Posts: 48,827 Points: -13,348
|
Have you tried unscrewing the chuck and turning the collet end over end, as one end has a larger collect bore than the other..
|
|
|
Rank: Pro Groups: Registered
Joined: 30/08/2012 Posts: 336 Points: 857 Location: London
|
Yes, tried that, but it just doesn't seem to want to grip the drill bits.
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,252 Points: 23,844 Location: East midlands
|
[quote=RobT]Yes, tried that, but it just doesn't seem to want to grip the drill bits.[/quote Hi all Have had the same problem with a miniature hand drill, but cured the problem with a piece of very thin card between the spindle and the outer sleeve, it gives a tighter clamp on the inner spindle . Hope this may help Regards Delboy271155 (Derek) COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
|
|
|
|
|
It's really strange but after years of perfect drilling my own pin vice suddenly stopped gripping the smallest drill bits, about 0.7mm or thereabouts. I managed to get over it by cutting a 1cm length of thin plastic insulation from a bit of 7/.02mm wire and (with some effort) slipped it over the drill shank. Works fine now but why it suddenly went like that I've no idea!  Might also work (and easier) with very thin heat shrink as well. Robin First wooden ship: The Grimsby 12 Gun 'Frigate' by Constructo Second: Bounty DelPrado Part Works Third: HMS Victory DelPrado Part Works 1/100 scale Diorama of the Battle of the Brandywine from the American Revolutionary War Diorama of the Battle of New Falkland (unfinished sci-fi), Great War Centenary Diorama of the Messines Ridge Assault Index for the Victory diary is on page 1
|
|
|
 Rank: Newbie Groups: Registered
Joined: 03/10/2012 Posts: 3 Points: 9 Location: London
|
Hi Rob,
I had the same problem with finding something small enough to hold the drill bits, then I found an archimedian drill and found that this works prefectly.
You can get these from any good model shop, I got mine on ebay for about £5.00.
Hope this helps.
Andy M
|
|
|
Rank: Pro Groups: Joined: 24/08/2009 Posts: 48,827 Points: -13,348
|
RobT wrote:Yes, tried that, but it just doesn't seem to want to grip the drill bits. I sounds like the chuck has flared, so that when it is tightened the collet does not nip up.
Time for a new one but possibly of another type., I have found the Citadell pin drill to be superb quality and nice to use, as it has a rubber head and twist grip, generally found at Games Workshop..
|
|
|
Rank: Pro Groups: Registered
Joined: 27/10/2012 Posts: 146 Points: 427 Location: London
|
|
|
|
 Rank: Vice-Master   Groups: Registered
Joined: 23/03/2010 Posts: 507 Points: 1,571
|
I just snip the head off one of the pins and put it in my cordless drill, have to be steady so as not to bend the pin willz attached the following image(s):
|
|
|
|
|
I have used a pin drill witch works well Building ?
Completed. Soliei Royal . Sovereign of the Seas . Virginia . Scotland . San Felipe . Corel vasa , Santisima Trinadad X section , Vasa
Next Build ?
When sailors have good wine, They think themselves in heaven for the time. John Baltharpe
|
|
|
 Rank: Beginner Level 2  Groups: Registered
Joined: 08/02/2013 Posts: 14 Points: 42 Location: Warrington, UK
|
Hi, I come from railway modelling where this is one of the main tool suppliers used. Cost-effective, fast and reliable. http://www.squirestools.com
|
|
|
|
Guest (2)
|
US
