|
|
Rank: Administration        Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,252 Points: 23,844 Location: East midlands
|
Hi all,  Just checking before I progress any further about the hull planking. I have got one more row of planking(number 7) to finish issue 19, so checking on what was coming up in issue 20, I noticed that there should be 10 rows of planks to get us down to the lowest point of the Transom. At this point I took 4 pieces of scrap bamboo to replicate planks 7-10 and the piece that would be plank 9 is very close to the lowest part of the Transom, so the question is, do I make slight tapers on planks 7-9 so that plank 10 fits ok?, or do I use only 9 planks and fit a spacer of some sort?. I have checked the official build and there doesn`t seem to be any mention of tapering the stern planks. Any advice will be gratefully accepted Regards delboy271155 (Derek) PS, Blind as a bat springs to mind, no mention of tapering in mag, but there is in the official build (sorry Mr T, missed it) COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
|
|
|
|
|
Hi Derek I think it would be ok to taper 7-9 toget a full strip at the transom.  Its alot of faf with thin bits  See Mr Ts build Building ?
Completed. Soliei Royal . Sovereign of the Seas . Virginia . Scotland . San Felipe . Corel vasa , Santisima Trinadad X section , Vasa
Next Build ?
When sailors have good wine, They think themselves in heaven for the time. John Baltharpe
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,252 Points: 23,844 Location: East midlands
|
Martyn Ingram wrote:Hi Derek I think it would be ok to taper 7-9 toget a full strip at the transom. Its alot of faf with thin bits Cheers Martyn, Just read the official build again and it does mention tapering  Regards delboy271155 (Derek) COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
|
|
|
|
|
|
|
|
|
|
Hi Derek, you really do have to taper at least planks 8,9 & 10 plus I bevelled the joining edges too.... Keep at it my friend....
Regards
Alan
|
|
|
Rank: Administration Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds Joined: 09/11/2012 Posts: 8,252 Points: 23,844 Location: East midlands
|
Gandale wrote:Hi Derek, you really do have to taper at least planks 8,9 & 10 plus I bevelled the joining edges too.... Keep at it my friend....
Regards
Alan Cheers Alan Did notice after my post that the mag didn`t mention tapering at the stern, but the official build did and I missed it Done a bit of a dry fit session and tapered 7-9 and that gave me a full plank at 10 when it starts to turn across the bottom of the transom. Got plenty of time for the next week as the Doc signed me off for another week and upped the strength of the pain killers. Happy building Regards delboy271155 (Derek) COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
|
|
|
|
|
delboy271155 wrote:Gandale wrote:Hi Derek, you really do have to taper at least planks 8,9 & 10 plus I bevelled the joining edges too.... Keep at it my friend....
Regards
Alan Cheers Alan Did notice after my post that the mag didn`t mention tapering at the stern, but the official build did and I missed it Done a bit of a dry fit session and tapered 7-9 and that gave me a full plank at 10 when it starts to turn across the bottom of the transom. Got plenty of time for the next week as the Doc signed me off for another week and upped the strength of the pain killers. Happy building Regards delboy271155 (Derek) Fingers crossed you get back to your old self very very soon..... Regards Alan
|
|
|
|
Guest
|
US
