|
|
 Rank: Pro    Groups: Registered
Joined: 17/03/2010 Posts: 215 Points: 617 Location: Blackburn
|
May i ask what is the best way of removing the dust after sanding down, the reason i ask is because on my other build i have used sanding sealer and when sanded leaves a fine dust on the hull which is very difficult to remove all of it. Thanks in advance.
|
|
|
Rank: Pro   Groups: Registered
Joined: 02/04/2010 Posts: 491 Points: 1,460 Location: Poole
|
Tacky cloths (resin impregnated) can usually be bought from a decent car accessory or hardware store - they are perfectly balanced between being 'sticky' enough to remove every last speck of dust that they come in contact with yet do not leave a residue. It may be cheaper to buy these online, in bulk, from spray shop suppliers - they can be quite expensive when bought in small numbers but they are a godsend when prepping for spraying . A cheaper, but less efficient method is to simply wipe your model down with a white spirit dampened (lint free) rag, this will remove a lot of unwanted debris, but for the best result, tacky cloths are best. Schnellboots on back burner
Tools.
|
|
|
Rank: Pro Groups: Registered
Joined: 17/03/2010 Posts: 215 Points: 617 Location: Blackburn
|
Thanks Capt just got some of Ebay £4.30 for 10.
|
|
|
 Rank: Vice-Master Groups: Registered
Joined: 26/03/2010 Posts: 600 Points: 1,959 Location: Solway West Cumbria
|
|
|
|
Rank: Pro Groups: Joined: 24/08/2009 Posts: 48,827 Points: -13,348
|
Hi shipmates!  I use an air compressor with a blow gun set to a very low pressure.  Just sufficient to take way the dust, but not to cause damage, as the air blows into all the little corners where you can't get in with a cloth.  The only thing is you MUST CHECK THE AIR PRESSURE FIRST! or it will blow across the room and smash off the wall!.  At least it's a quick and easy way to get rid of the dust, best done outside then there's less mess.  I know get the pressure wrong and you get to start all over again. 
|
|
|
 Rank: Super-Elite     Groups: Registered
Joined: 04/04/2010 Posts: 3,955 Points: 11,809 Location: uk
|
son of bulwark. humph!! where do you work in a grand prix team??? where would would we get a 10 bar air compressor??? you got a paint shop??? we only want to wipe of a bit of dust.bet your wife love the sound of that compressor starting up. Current builds: SotS, USS Consitution, San Felipe, D51 loco, HMS Surprise, RB7, Arab Dhow, Jotika HMS Victory Completed builds: HMS Pickel, Thermopylae, Mississipi river boat, Mary Rose, Cutty Sark, San Francisco II, HMS Victory x5, Titanic Lifeboat, Panart HMS Victory Launch, Hachette Titanic, Virginia Schooner, Endeavour Longboat. http://www.model-space.com/gb/
|
|
|
 Rank: Master Groups: Registered
Joined: 20/03/2010 Posts: 1,199 Points: 3,473 Location: Glenrothes
|
i just ask the mrs to hold her breath for 30seconds (if possible) hold launch in front of face then tell her to carry on mind u dont burn ure fingers tho (did i mention i like hospital food)
|
|
|
Rank: Master Groups: Registered
Joined: 15/04/2010 Posts: 1,266 Points: 3,841 Location: The Quantock Hills,Somerset
|
I agree with compressed air being a good duster..but you don't need a compressor...just buy a tin of computer air duster from asda etc...about £5,as you will only need a quick blast here & there it should last a while.I use it all the time when building & servicing pc's. Rob Nolli Illigitimi Carborundum!!!Current Builds: HMS Victory, SV Thermopylae
|
|
|
Rank: Pro Groups: Joined: 24/08/2009 Posts: 48,827 Points: -13,348
|
Hi Shipmates! Glad to see your all in good spirits after all the problem DeAGOSTINI have given us! Hello karl113! I don't work in a grand prix team! I'm disabled and no wife to complain about sound. I had a 24 Ltr. 8 bar compressor in my shed for other jobs (very good for cleaning bag-less hovers, but need to keep out of the way of dust cloud). At 10 bar your launch would blow-up not fly across the room.  Hello to Dontshootme as well! When I run out of air I just turn the compressor on to refill the main tank, no need to go to asda to buy a tin. So I can keep my £5.00 and spend it on something else, instead of blowing another £5.00
|
|
|
Rank: Pro Groups: Registered
Joined: 17/03/2010 Posts: 215 Points: 617 Location: Blackburn
|
Thanks for your replies and suggestions, sadly i dont have a compressor but tried a hoover and works a treat, why didnt i think of that before asking!!!
|
|
|
Rank: Pro  Groups: Registered
Joined: 20/03/2010 Posts: 278 Points: 833 Location: Nottingham
|
You guys are so bad! bet your respective Mrs dont get to read your posts!  Pam's shipyard is closed for now no more room!
|
|
|
Rank: Master Groups: Registered
Joined: 15/04/2010 Posts: 1,266 Points: 3,841 Location: The Quantock Hills,Somerset
|
My wife stands behind everything I say..& hits me when she...ow that hurt!!!! Rob Nolli Illigitimi Carborundum!!!Current Builds: HMS Victory, SV Thermopylae
|
|
|
 Rank: Beginner Level 3 Groups: Registered
Joined: 23/04/2010 Posts: 25 Points: 75
|
andylangtree wrote:May i ask what is the best way of removing the dust after sanding down, the reason i ask is because on my other build i have used sanding sealer and when sanded leaves a fine dust on the hull which is very difficult to remove all of it. Thanks in advance. You might also -in view if other advice- want to consider a wide (as in 1") paint brush and a strip of 'duck-tape'. Go over the sanded area with your brush in 'stabbing' strokes (sweeping each time to the front of whatever you've sanded) and then finish off with a strip of duck tape pressed into the same surface then swiftly peeled off. Prime the area thereafter and any minor imperfections highlighted as a result ,deal with accordingly. ;)
|
|
|
Rank: Beginner Level 3 Groups: Registered
Joined: 23/04/2010 Posts: 25 Points: 75
|
Dontshootme wrote:I agree with compressed air being a good duster..but you don't need a compressor...just buy a tin of computer air duster from asda etc...about £5,as you will only need a quick blast here & there it should last a while.I use it all the time when building & servicing pc's. Compressed air doesn't do the deed on wood as a result of the micro fibres in the wood grain trapping such waste material. As I've mentioned to another on this site, use a 1" brush with stabbing motions (to the front of the sanded object)and finish by laying a strip of 'duck tape' over the same area to pick any residual waste.
|
|
|
|
Guest (2)
|
US
