|
|
 Rank: Beginner Level 1 Groups: Registered
Joined: 31/05/2012 Posts: 9 Points: 27
|
when I cut my lower gunports, (checked and rechecked measurements) my aft gunport is right in the middle of a frame. anyone else had this prob?
|
|
|
|
|
Hi vindicari post some pics to see if we can help rgd Martyn Building ?
Completed. Soliei Royal . Sovereign of the Seas . Virginia . Scotland . San Felipe . Corel vasa , Santisima Trinadad X section , Vasa
Next Build ?
When sailors have good wine, They think themselves in heaven for the time. John Baltharpe
|
|
|
 Rank: Master       Groups: Registered
Joined: 05/09/2012 Posts: 1,400 Points: 4,690 Location: Beaminster, Dorset
|
Hi, The aft port on the lower level, should sit alongside the frame, to the right of it. However on the build this is a closed port, so as long as this is not an indication of a deeper problem it should not matter that the frame is in the middle.
|
|
|
Rank: Beginner Level 1 Groups: Registered
Joined: 31/05/2012 Posts: 9 Points: 27
|
ah all is explained, it is a closed port. many thanks.
|
|
|
 Rank: Newbie Groups: Registered
Joined: 28/11/2013 Posts: 3 Points: 9 Location: France
|
Hello,
I am french and new on this forum.
In France we just received issue N° 35 of the Sovereign of the Seas and I have a querry regarding the ports.
In this issue, step 26 ask to drill a hole in the center of the ports.
I wonder what is the use of this hole, do we have to drill the reinforcement as well?
Thank You in advance.
Best Regards.
Jean-paul
|
|
|
|
|
tadgoz wrote:Hello,
I am french and new on this forum.
In France we just received issue N° 35 of the Sovereign of the Seas and I have a querry regarding the ports.
In this issue, step 26 ask to drill a hole in the center of the ports.
I wonder what is the use of this hole, do we have to drill the reinforcement as well?
Thank You in advance.
Best Regards.
Jean-paul
Hi Jean-Paul and welcome to the forum where advice and assistance from members is readily available... The hole you are to drill in the centre of gun ports is to enable you to fit the dummy gun barrels.... These ports do not carry full gun kits, only the barrels.... Hope this helps. Regards Alan
|
|
|
|
|
tadgoz wrote:Hello,
I am french and new on this forum.
In France we just received issue N° 35 of the Sovereign of the Seas and I have a querry regarding the ports.
In this issue, step 26 ask to drill a hole in the center of the ports.
I wonder what is the use of this hole, do we have to drill the reinforcement as well?
Thank You in advance.
Best Regards.
Jean-paul
Hi Jean-paul and welcome to the forum.
You should follow the instructions carefully. Normally the hole in the hull allows you to cut out the gun port. the hole in the support is for you to fit the dummy canons later in the build. Doing this now gives you a centre hole so your cannons will all be dead centre to the gun port.
Dont do this unless that is what the instructions say to
Jase“Whenever you find yourself on the side of the majority, it is time to pause and reflect.”
-Mark Twain
|
|
|
Rank: Newbie Groups: Registered
Joined: 28/11/2013 Posts: 3 Points: 9 Location: France
|
Thanks to Alan and Jase for their help.
I suspected that, but I was not sure...
Best Regards.
Jean-paul
|
|
|
|
Guest (2)
|
US
