Welcome Guest Search | Active Topics | Log In | Register

Perfecting the spotting top ribs. Options
Previous Topic · Next Topic
jase
#1 Posted : 19 April 2014 14:42:20

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 21/03/2010
Posts: 7,582
Points: 21,739
The spotting top ribs is one are the instructions are a little cage about. 'glue the 27 ribs in place referring to the plan' so this is my how to guide - hope it is useful BigGrin

1. mark out the positions of the ribs using the plans.


2. sand one end of your 2x5mm plank so it sits flush with the edge and is at the correct angle as per your marked out plan (don't forget your measuring from the upper edge. mark out the length of the rib and saw off slightly longer to give you some wriggle room


3. mark out the step that needs to be cut into the rib. (don't assume it will always be the same do this for every rib). mark both sides and connect up all the points so you have a mark on all sides.



4. file out the step using a corse square needle file.. I use a diamond cut type. test fit the rib and adjust as necessary until you have a nice snug fit.



5. Once you are happy with the fit mark out the other end of the rib on both sides and sand this to shape. Keep test fitting until it is perfect.





6. measure 1mm from the bottom of the rib and mark off, then draw a line from your mark to the top corner, this will be your sanding line.


7. clamp your rib in a vice or similar and sand down to your line. A barrel sander in a rotary tool is perfect for this. If using a power tool stop above the sand line and finish off by hand.



8. Once you have sanded down we can finish the rib. Using a circular motion gently sand all exposed sides on 1800 micro-mesh (if you are staining this will remove any remaining pencil marks) then repeat with 3200 grit micro-mesh



9. Test fit again before fixing in place. Glue in place and wipe away any excess with a tissue. if you cannot get in to wipe away then after a few seconds you should be able to scrap away any excess adhesive with a cocktail stick



Once the glue is dry sand down the top of the rib flush with the top of the upper surround and finish with the two micro-mesh pads so it is nice and smooth.



It should take about 15 - 20 mins to do each rib, so a few hours work but your results will be worth the time.

Jase
“Whenever you find yourself on the side of the majority, it is time to pause and reflect.”
-Mark Twain
Back to top
 Report Abusive | Report SPAM
Gandale
#2 Posted : 19 April 2014 15:29:24

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered, Global Forum Support, Moderator, Official Builds, Administrators

Joined: 08/09/2012
Posts: 15,172
Points: 46,151
Location: Aberdeen
Great little tutorial and great results too Jase, very well done.... Cool Cool .. Will be helpful to a lot of builders who have yet to reach this stage.... Cool Cool

Regards

Alan
Back to top
 Report Abusive | Report SPAM
stevie_o
#3 Posted : 19 April 2014 16:38:17

Rank: Super-Elite

Active Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered

Joined: 30/01/2013
Posts: 4,604
Points: 13,607
Location: Monmouthshire UK
Back to top
WWW  Report Abusive | Report SPAM
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.184 seconds.
DeAgostini