Welcome Guest Search | Active Topics | Log In | Register

Ironman Official Build Issues 63 - 66 Options
Previous Topic · Next Topic
admin
#1 Posted : 12 August 2023 17:44:58
Rank: Administration


Groups: Administrator, Administrators, Forum Support Team, Global Forum Support, Global Forum Support Team, Moderator, Official Builds

Joined: 24/08/2009
Posts: 1,909
Points: 5,743
Location: UK
Hi All, BigGrin

Well while I`ve got the chance, thought I`d post the next Ironman update for Issue 63. Blink

Starting this pack we will construct the Calf Armour Plate for the right leg.

Pic 1 shows the parts supplied.

Pic 2 shows you the orientation of the two parts of the calf hinge and where to secure the hinge together using two LP screws.

Now locate the hinge in its place as shown in Pic 3 and secure it with two EM screws as in Pic 4.


Well that`s all for this issue. Pic 5.


See you soon for the next updates issues 64 - 66.


Regards
delboy271155
(Derek)
admin attached the following image(s):
1.jpg
2.jpg
3.jpg
4.jpg
5.jpg
Back to top
 Report Abusive | Report SPAM | Edit by user: 12/08/2023 18:02:19 | Reason: Not specified
delboy271155
#2 Posted : 14 August 2023 14:53:19
Rank: Administration

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds

Joined: 09/11/2012
Posts: 7,965
Points: 23,084
Location: East midlands
Hi All, I`m back BigGrin

It`s UPDATE time. This one is for issue 64 where the Upper Shin Plate is attached to the right leg, all parts supplied are shown in Pic 1.

Start by removing the paper off one side of a piece of double sided tape the second piece is a spare) and position the tape inside the upper shin plate as shown in Pic 2.

Having removed the other paper from the double sided tape, carefully position the plate into position. Note: care must be taken when fitting the shin plate as the curved sections at the top of the plate have to be flexed outwards to fit the part. Pic 3 shows the location indicated by the yellow lines and Pic 4 the part in place.

Along with the double sided tape the shin plate is fixed using two EM screws as indicated in Pics 5 and 6.

To finish press fit the right and left gold side plates, noting they will only fit on their correct sides. Shown in Pics 7 and 8.

That`s it for this update, but be sure to keep the Hip Joint Cover safe for use in a later stage. Pic 9


Regards
delboy271155
(Derek)
delboy271155 attached the following image(s):
1.jpg
2.jpg
3.jpg
4.jpg
5.jpg
6.jpg
7.jpg
8.jpg
9.jpg
COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
Back to top
 Report Abusive | Report SPAM
delboy271155
#3 Posted : 15 August 2023 19:26:49
Rank: Administration

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds

Joined: 09/11/2012
Posts: 7,965
Points: 23,084
Location: East midlands
Hi All, BigGrin

This is the update for Issue 65 and it seems we have turned a corner, in as much that we are now starting on the middle of the armour.

In this issue we will construct the Central Leg Support. Not a lot to do, but it can be a bit fiddley so take care with positioning the parts.Blink

Bored Bored Parts supplied in Pic 1.

Make a start by positioning the spring onto the post at the end of the Spring Holder. Pic 2.

Now this is the "fiddley" bit.Blink

Place the Leg Support 2 (65B) with the flat side on the work surface. Then whilst holding the spring and its holder together, place them into position inside the Leg Support as shown in Pic 3.

Finally, making sure that the Spring and its Holder stay in the correct position, place the other Central Leg Support (65A) on top. With all the parts aligned the assembly can be fixed together as shown in Pic 4 by three LP screws. Note: As also shown in Pic 4 the assembly will not close together unless the pivot pin of the Spring Holder is in the correct place as shown.

So, that`s it for this update. Issue 66 will be up soon at which point we will have completed another pack.Woot Woot Woot Woot


Take care and be nice to each other.BigGrin


Regards
delboy271155
(Derek)
delboy271155 attached the following image(s):
1.jpg
2.jpg
3.jpg
4.jpg
COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
Back to top
 Report Abusive | Report SPAM
delboy271155
#4 Posted : 16 August 2023 17:13:23
Rank: Administration

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsTurquoise Medal: Turquoise Medal for model making know-how contributionBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Registered, Forum Support Team, Administrators, Global Forum Support Team, Moderator, Official Builds

Joined: 09/11/2012
Posts: 7,965
Points: 23,084
Location: East midlands
Hi Everyone, BigGrin

Well, here we go with the update for Issue 66, the last for this pack.Cool This is the Central Leg Support Part 2.

Like the last update, not a lot to do but a little fiddley. Part positioning is critical though.

Parts supplied are shown in Pic 1.

To start, position the Shell with the inside surface facing up and position the spring onto the pin as shown in Pic 2.

Bring the Support for the Spring to the table and note that one side has a pin inside a circle. this side is the underside that will sit on top of the spring you just positioned inside of the Shell.

Then following the orientation of Pic 3, position the Spring Support over the Spring and secure it using two BP screws. The yellow lines emphasise the angled ends of the Support. Having tightened the two BP screws, check that the Spring is securely located, exactly as shown in Pic 4.

That completes this update, so keep the two rotational bases (numbered 1 and 2 in the instructions) safely for use at a later stage. Pic 5.


I found that the assembly just made and the unused parts fit nicely back into the plastic moulds they came in. Can`t get much safer than that.Blink


Keep safe and well. Hope to see you all again soon for the update of Issue 67 which starts the next pack.ThumpUp Woot ThumpUp


Regards
delboy271155
(Derek)Admin

delboy271155 attached the following image(s):
1.jpg
2.jpg
3.jpg
4.jpg
5.jpg
6.jpg
COME BACK GUY FAWKES "YOUR COUNTRY NEEDS YOU"
Back to top
 Report Abusive | Report SPAM
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.262 seconds.
DeAgostini