Welcome Guest Search | Active Topics | Log In | Register

BTTF Delorean Official build PACK 1 Options
roymattblack
#1 Posted : 01 February 2024 17:36:29

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered

Joined: 04/06/2011
Posts: 4,155
Points: 12,607
Location: ipswich
STAGE 1:

The parts supplied will enable you to begin constructing the rear body panel of the car.

Locate parts 1B & 1C.
Clip the parts together and fix in place using 4 x BP screws fitted from the rear of the parts.

Locate the parts to assemble the right rear light – 1G, 1H, 1I, 1J, 1K.
Fit the parts together as shown in the picture. The parts will only fit one way.
When assembled, fit the light to the right side of the rear panel by sliding the tab on the slanted edge of the light unit into the slot in the metal body panel.
Fix the light unit in place using 1 x BP screw from the rear.

Locate the licence plate and the small pack containing two sticker sheets.
There are doubles of each sticker in case of loss or error.
Carefully peel one of the ‘red’ stickers from the backing paper and place it on the licence plate on the upper left side in the space between the orange stripes.
Repeat with one of the ‘yellow’ stickers, placing it on the upper right of the licence plate.

Locate the licence plate support base – part 1D.
The licence plate fits in the central recess and will only fit one way up.
Turn the assembly over and fix the parts together using 2 x AP screws.

Locate the licence plate light strip – part 1L.
This part fits over the upper edge of the licence plate assembly so that the two small tabs on the rear sit over the two locating points on the licence plate base.
Fix the parts together using 2 x AP screws.

Locate the rear bumper – part 1A.
Carefully fit this into place on the rear body panel.
There are 4 x tabs on the part that will clip into the four slots in the body section.
The bumper will only fit one way up.

Store all of your parts safely for now.

roymattblack attached the following image(s):
P1012792.JPG
P1012793.JPG
P1012794.JPG
P1012795.JPG
P1012797.JPG
P1012799.JPG
P1012800.JPG
P1012802.JPG
P1012803.JPG
P1012804.JPG
P1012805.JPG
P1012806.JPG
P1012807.JPG
P1012808.JPG
P1012809.JPG
P1012810.JPG
P1012811.JPG
P1012812.JPG
P1012814.JPG
P1012815.JPG
P1012816.JPG
roymattblack
#2 Posted : 01 February 2024 20:22:36

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered

Joined: 04/06/2011
Posts: 4,155
Points: 12,607
Location: ipswich
STAGE 2:

The parts supplied will enable you to begin constructing part of the car bodywork and complete the rear section started in the previous stage.

Locate the metal front wing of the car and the two plastic trim strips – parts 2A, 2B & 2C.
The long trim strip fits in the recess in the front wing just behind the wheel arch. The piece will only fit one way.
Secure the trim strip from the other side of the body panel using 2 x AP screws.
The short trim strip fits in the recess in front of the wheel arch and is secured using 1 x AP screw.

Assemble the left rear light in the same way as the other light in stage 1.
Fit the light to the rear body section and secure using 1 x BP screw as before.

Retrieve the previously assembled licence plate and fit it in place on the rear body section between the lights. It will only fit one way.
Secure the part from the other side of the body section using 2 x AP screws.

Store the parts safely until they are needed in the future. (No pun intended…)

roymattblack attached the following image(s):
P1012818.JPG
P1012819.JPG
P1012820.JPG
P1012823.JPG
P1012824.JPG
P1012825.JPG
P1012826.JPG
P1012828.JPG
P1012829.JPG
P1012830.JPG
P1012831.JPG
P1012832.JPG
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.187 seconds.
DeAgostini