Welcome Guest Search | Active Topics | Log In | Register

Chevrolet Nascar Official Build stages 1 - 2 Options
roymattblack
#1 Posted : 30 January 2025 13:16:01

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered

Joined: 04/06/2011
Posts: 4,565
Points: 13,855
Location: ipswich
STAGE 1:

This build promises to be great fun.
roymattblack attached the following image(s):
P1010135.JPG
roymattblack
#2 Posted : 31 January 2025 10:38:08

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered

Joined: 04/06/2011
Posts: 4,565
Points: 13,855
Location: ipswich
STAGE 1:

Locate the bonnet, part 1A, the catch surrounds, parts 4 x 1B and the ZM screws.

The screws are extremely small so take great care when fitting them.
It is advisable to clean out the screw location holes in the bonnet from any paint or swarf using the tip of a sharp blade.
Be very careful not to damage the paint on the bonnet.
Hold one of the catch surrounds in place with a fingertip and fit the screws, 2 x ZM.

Do not fully tighten them until they are both fitted.

It cannot be emphasized enough, to take care here.
A slip with the screwdriver could seriously damage the paintwork.


Fit the other three catch surrounds in the same way.

Store the assembly and unused parts safely for now.
roymattblack attached the following image(s):
P1010137.JPG
P1010138.JPG
P1010139.JPG
P1010142.JPG
P1010143.JPG
P1010144.JPG
roymattblack
#3 Posted : 02 February 2025 11:54:21

Rank: Super-Elite

Publisher Medal: Featured Build of the MonthActive Service Medal: 500 post active service MedalPurple Medal: Super active service medal for 1000 postsOutstanding Build: An award for an outstanding buildBuild-Diary Medal: Build-Diary Medal of HonourRed Medal: Red Medal
Groups: Official Builds, Administrators, Moderator, Global Forum Support, Registered

Joined: 04/06/2011
Posts: 4,565
Points: 13,855
Location: ipswich
STAGE 2:

In this stage you will assemble the front of the car body.

Locate the body panel and the upper grille, parts 2A and 2B.

Fit the grille in place and secure using 3 x YM screws.
Take great care not to damage any surrounding paint work.
Do not over tighten the screws as this will create a ‘dent’ in the thin metal.

Fit the lower vent mesh and frame, parts 2C and 2D in place over the large lower vent on the body panel.
Secure the parts using 6 x YM screws. As before, do not over tighten the screws.

You will find it easier to fit the screws if you clear the mesh from the screw holes using a cocktail stick.

Retrieve the mesh and frames, parts 2 x 1C and 2 x 1D from the previous stage.
Fit the mesh and then the frames over the vents on either side of the body panel and fix them using 4 x YM screws on each frame.
As before, do not over tighten the screws.

Store the assembly safely for now.
roymattblack attached the following image(s):
P1010145.JPG
P1010147.JPG
P1010152.JPG
P1010153.JPG
P1010154.JPG
P1010155.JPG
P1010156.JPG
P1010157.JPG
P1010158.JPG
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Powered by YAF | YAF © 2003-2009, Yet Another Forum.NET
This page was generated in 0.135 seconds.
DeAgostini